Схема узла
Запчастини для посудомийної машини Bauknecht GSIP 6598/1 IN
Виберіть версію / індустріальний код: * Від обраної версії залежить сумісність запчастин
854659801710
Характеристики:
Fan for drying: Voltage 220/240 V (min.) | 220 V |
Water pressure: Inlet pressure | 0.3 bar - 10 bar |
Rotations: Drain pump motor | 3000 RPM |
Detergent capacity: Rinse aid dosage | 135 cm 3 |
Dimensions + Weight: Wooden door (Height) | 515 mm - 600 mm |
Electronic boards: Serial boards (Data set) | 730621 |
Dimensions + Weight: Wooden door for Integrable types (Weight) | max. 5.5 kg |
Flow rates/ Inlet volume: Shower/Spray arm top | ~ 8 l/min |
Spray pump motor: Voltage | 220/240 V |
Heating element: Temperature on surface | ~ 115 °C |
Flow rates/ Inlet volume: Fan for drying | Total 900 l/min Primary air flow 210 l/min Secondary air flow 780 l/min |
Water softener setting | Härtebereich einstellen (nach folgender Tabelle): Gerät einschalten Programm 2 wählen Start-Taste drücken (mindestens 5 Sekunden) bis Start LED blinkt Start LED blinkt bzw. Digitalanzeige leuchtet entsprechend der eingestellten Härte (siehe Tabelle) Start-Taste kurz drücken ändert die Einstellung um 1 und beginnt nach 7 wieder bei 1 Gerät ausschalten (Einstellung gespeichert) To change the water softener setting:· Push the POWER button on · Change to program 2 · Hold the START button for 5 seconds until the LED is flashing · is shown by flashing LED or digital display · By pushing the START button you can change the setting · Push the POWER button off to save and exit the water softener setting |
Spray pump motor: HA | 60 Ω |
Detergent capacity: Prewash | 10 cm 3 |
Drain pump motor: Power Consumption | 30 W |
Coil of dispenser: Resistance | 1.3 k Ω |
Flow rates/ Inlet volume: Spray pump | 45 l/min - 65 l/min |
Electronic boards: Service boards () | siehe Ersatzteilliste |
Program information: | All programs will be locked after start. Changing the program or ?nishing the program will be possible only after pressing the start button for longer then 1.5 sec. (Break by customer) A switching off the appliance or unplug the appliance for a while, this will frozen the program step and later on, the program continuos on the same position. Exception: Switching off the appliance or unplug the appliance during the drying phase, this will lead directly to the end of the program. |
Spray arms, turning rhythm at alternating spray system: Intermediate rinse | Spray arm lower ~2min Upper arm ~2min Spray arm upper ~ 2 min |
Електричні базові дані: напруга | 220/ 240 V |
Spray pump motor alternating spray system: Capacitor | 4 µ F |
Heating element: Safety thermostat self reset (Temperature of water) | 85 °C |
Rotations: Spray pump motor | 2800 RPM |
Motor Diverter Valve: Signal (2x within ~13 sec.) | 5.0 V |
Heating element: | 1 Element system |
Electronic boards: Serial boards (Basic UCB, not programmed) | 4619 727 06181 siehe Boardaufdruck |
Single electric water inlet valve: Resistance | 3.76 k Ω |
Data Energy Label: Drying Performance | A |
Single electric water inlet valve: Voltage | 220/ 240 V |
Heating element: Power Consumption | 1.87/ 2.04 kW |
Regeneration valve: Frequency | 50/ 60 Hz |
Rotations: Spray arm upper | 30 RPM - 40 RPM |
Flow rates/ Inlet volume: Pump height max. | 1.1 m |
Flow rates/ Inlet volume: Spray arm lower | ~ 33 l/min |
Dimensions + Weight: Wooden door for Integrable types (Width) | 592 mm - 595 mm |
Dimensions + Weight: Wooden door for Integrable types (Max. stick out over lower edge of appliance door) | 92 mm |
Water softener: Resin container | 700 cm 3 |
Motor Diverter Valve: Voltage | 220 V - 240 V |
Electronic boards: Serial boards (UB) | 4619 724 86781 |
Heating element: Voltage | 220/ 240 V |
Flow rates/ Inlet volume: Inlet valve | 4 l/min |
Accessory: | If you need spare parts apart from the spare part list have a look in the Service Bulletin 4812 718 40084. For higher mounted Dishwashers to prevent the drain off effect - also usable for lower drain pipes and to prevent the failure F8 use Kit 4812 310 18993. |
Fan for drying: Voltage 220/240 V (max.) | 240 V |
Water softener: Salt container | 2 kg |
Spray pump motor: HI | 79 Ω |
Spray pump motor: Capacitor | 4 µ F |
Dimensions + Weight: Wooden door (Max. stick out over lower edge of appliance door) | 92 mm |
Options: | Multizone Delay function |
Electronic boards: Serial boards (CB programmed) | 730631 |
Dimensions + Weight: Wooden door for Integrable types (Height of plinth) | min. 93 mm |
Regeneration: Volume | 300 cm 3 |
Drain pump motor: Voltage | 220/ 240 V |
Spray arms, turning rhythm at alternating spray system: Final rinse | Spray arm lower ~2min Upper arm ~2min Spray arm upper ~ 2 min |
Detergent capacity: Dosage steps | 1 ml - 6 ml |
Electrical base data: Total power | 2.0 kW - 2.2 kW |
Coil of dispenser: Frequency | 50/ 60 Hz |
Spray pump motor alternating spray system: Power Consumption | 125 W |
Regeneration: after wash cycles | abhängig von der Wasserhärte Depending on the water hardness |
Dimensions + Weight: Product dimensions (Weight) | 50 kg |
Dimensions + Weight: Wooden door for Integrable types (Height) | 515 mm - 600 mm |
Water hardness: Water hardness German degrees °dH French degrees °fH English degrees Clarke °e mmol/l Water softener setting is shown by flashing LED (1x-7x) | 1 soft 0 - 5 0 - 9 0 - 6,3 0 - 0.9 1 x 1 - 2 soft/ medium 6 - 10 10 - 18 7 - 12.6 1 - 1.8 2 x 2 medium 11 - 15 19 - 27 13.3 - 18.9 1.9 - 2.7 3 x 3 medium/ hard 16 - 21 28 - 37 19.6 - 25.9 2.8 - 3.7 4 x (DEFAULT SETTING) 4 hard 22 - 28 38 - 50 26.6 - 35 3.8 - 5.0 5 x 4 very hard 29 - 35 51 - 63 35.7 - 44.1 5.1 - 6.3 6 x 4 extremely hard 36 - 60 (53) 64 - 107 44.8 - 74.9 6.4 - 10.7 7 x 1 weich 0 - 5 0 - 9 0 - 6,3 0 - 0.9 1 x 1 - 2 mittel 6 - 10 10 - 18 7 - 12.6 1 - 1.8 2 x 2 mittel 11 - 15 19 - 27 13.3 - 18.9 1.9 - 2.7 3 x 3 mittelhart 16 - 21 28 - 37 19.6 - 25.9 2.8 - 3.7 4 x (Werkseinstellung) 4 hart 22 - 28 38 - 50 26.6 - 35 3.8 - 5.0 5 x 4 sehr hart 29 - 35 51 - 63 35.7 - 44.1 5.1 - 6.3 6 x 4 äußerst hart 36 - 60 (53) 64 - 107 44.8 - 74.9 6.4 - 10.7 7 x |
Flow rates/ Inlet volume: Spray arm upper | ~ 27 l/min |
Heating element: Fuse | 206 °C |
Motor Diverter Valve: Frequency | 50/ 60 Hz |
Regeneration valve: Resistance | 3.13 k Ω |
Electronic boards: Serial boards () | Programing of version and programmed control board, see "Service" and "Data set" on rating plate of inner door: |
Data Energy Label: Energy Performance | A |
Flow rates/ Inlet volume: Flow meter | 208 lmp/l |
Data Energy Label: Reference program | A5e |
Розміри + Вага: Розміри продукту (ширина) | 59.7 cm |
Drain pump motor: Resistance | 146 Ω |
Succession of programs: Programs () | see program diagram |
Spray pump motor alternating spray system: HI | 79 Ω |
Dimensions + Weight: Wooden door for Integrable types (Thickness) | 16 mm - 20 mm |
Електричні базові дані: частота | 50 Hz |
Електричні базові дані: Споживаюча потужність | 2,0 kW - 2,2 kW |
Spray arms, turning rhythm at alternating spray system: Prewash | Spray arm lower ~3min Upper arm ~1min Spray arm upper ~ 1 min |
Coil of dispenser: Voltage | 220/ 240 V |
NTC | 20 °C 58.1 kΩ 25 °C 47.1 kΩ 30 °C 38.2 kΩ 40 °C 25.4 kΩ 50 °C 17.2 kΩ 60 °C 11.8 kΩ 70 °C 8.3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ 20 °C 58,1 kΩ 25 °C 47,1 kΩ 30 °C 38,2 kΩ 40 °C 25,4 kΩ 50 °C 17,2 kΩ 60 °C 11,8 kΩ 70 °C 8,3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ |
Regeneration: Salt consumption for regeneration | ~ 77 g |
Dimensions + Weight: Wooden door (Height of plinth) | min. 93 mm |
Електрична база даних: Запобіжник | 10 A |
Spray pump motor alternating spray system: Voltage | 220/ 240 V |
Water pressure: Spray pump pressure | 0.4 bar |
Розміри + Вага: Розміри продукту (Глибина) | 55.5 cm |
Spray arms, turning rhythm at alternating spray system: | Bemerkung: Nach Programmunterbrechungen im Testprogramm rotieren die Sprüharme wieder im Rhytmus des Hauptspülens (5/3 min). Wichtig: Zum Beenden des Testprogramms Startknopf länger als 1,5 s drücken. Nach Beendigung des Testprogramms (LED Ende an und/oder LED Start aus) muß das Gerät ausgeschaltet werden, andernfalls rotieren die Sprüharme beim nächsten Spülen weiter im Rhytmus des Testprogramms (30/30 s). |
Dimensions + Weight: Wooden door (Width) | 592 mm - 595 mm |
Spray arms, turning rhythm at alternating spray system: Service Test program | Remark: When switching of the main switch or interrupt the mains during the Test Program runs, then the alternating of the spray arms change in the test program to the rhythm of main wash 5/3 min. After finishing the test program (End LED shines and/or Start LED goes of) must the appliance be switched off. Spray arm lower ~30sec Upper arm ~30sec Spray arm upper ~ 30 s |
Regeneration valve: Voltage | 220/ 240 V |
Rotations: Fan for drying | 2500 RPM |
Dimensions + Weight: Wooden door (Weight) | max. 5,5 kg |
Detergent capacity: Main wash | 40 cm 3 |
Spray arms, turning rhythm at alternating spray system: Main wash | Spray arm lower ~3min Upper arm ~5min Spray arm upper ~ 5 min |
Water softener: Regeneration dosage | 300 cm 3 |
Heating element: Resistance | 24.5 Ω |
Water Volume: Water Volume Level | Regeneration 0.3 l 15 mm Back rinse 3x 1.0 l 60 mm Prewash 3.9 l 120 mm Main wash 3.2 l 118 mm Intermediate rinse 1 3.2 l 118 mm Intermediate rinse 2 3.2 l 118 mm Clear rinse 3.2 l 118 mm Safety/ overflow 8.5 l 141 mm Regenerieren 0,3 l 15 mm Rückspülen 3x 1,0 l 60 mm Vorspülen 3,9 l 116 mm Hauptspülen 3,2 l 112 mm Zwischenspülen 1 3,2 l 112 mm Zwischenspülen 2 3,2 l 112 mm Klarspülen 3,2 l 112 mm Sicherheitsniveau 8,5 l 141 mm |
Single electric water inlet valve: Frequency | 50/ 60 Hz |
Dimensions + Weight: Wooden door (Thickness) | 16 mm - 20 mm |
Spray pump motor: Power Consumption | 125 W |
Heating element: Heating speed | ~ 2.0 °C/min |
Rotations: Spray arm lower | 30 RPM - 40 RPM |
Spray pump motor alternating spray system: HA | 60 Ω |
Data Energy Label: Cleaning Performance | A |
Regeneration: Water hardness | 0 - 60 (53) °dh 0 - 10.7 mmol/l 0 - 107 °Fh |
Electronic boards: Serial boards (DLB) | 489911 |
Flow rates/ Inlet volume: Drain pump | 16 l/min |
Розміри + Вага: Розміри продукту (Висота) | 82.0 - 87.0cm |
Motor Diverter Valve: Resistance | 6.5 k Ω |
Regeneration: Number of cycles with 2 kg salt | ~ 26 |