Название: Запчасть для электропосудомоечной машины Whirlpool 481240448753
Недоступно к заказу
Номер на схеме: 9935
Артикул:482253280216
Название: Воронка Whirlpool 482253280216
Недоступно к заказу
Номер на схеме: 9936
Артикул:481246678386
Название: Отгораживание для электропосудомоечной машины Whirlpool 481246678386
Недоступно к заказу
Характеристики:
Water pressure: Inlet pressure
0.3 bar - 10 bar
Rotations: Drain pump motor
3000 RPM
Detergent capacity: Rinse aid dosage
135 cm 3
Electronic boards: Serial boards (Data set)
493055
Dimensions + Weight: Wooden door for Integrable types (Weight)
max. 5.5 kg
Regeneration: Position 0
after wash cycles 12
Water hardness 0 - 5 °dh 0 - 0.9 mmol/l 0 - 9 °Fh
Flow rates/ Inlet volume: Shower/Spray arm top
~ 8 l/min
Spray pump motor permant spray system: Voltage
220/ 240 V
Heating element: Temperature on surface
~ 115 °C
Potentiometer: Points of meassurement: (Position 2)
1.0 k Ω
Detergent capacity: Prewash
10 cm 3
Drain pump motor: Power Consumption
30 W
Coil of dispenser: Resistance
1.3 k Ω
Flow rates/ Inlet volume: Spray pump
45 l/min - 65 l/min
Regeneration: Position 5
after wash cycles 2
Water hardness 29 - 35 °dh 5.1 - 6.3 mmol/l 51 - 63 °Fh
Program information:
End - Acoustic signal
All programs will be locked after start. Changing the program or ?nishing the program will be possible only after pressing the start button for longer then 1.5 sec. (Break by customer)
A switching off the appliance or unplug the appliance for a while, this will frozen the program step and later on, the program continuos on the same position.
Exception: Switching off the appliance or unplug the appliance during the drying phase, this will lead directly to the end of the program.
Электрические базовые данные: напряжение
220/ 230 V
Heating element: Safety thermostat self reset (Temperature of water)
~ 85 °C
Rotations: Spray pump motor
2800 RPM
Heating element:
1 Element system
Electronic boards: Serial boards (Basic UCB, not programmed)
4619 724 84451
Single electric water inlet valve: Resistance
3.76 k Ω
Data Energy Label: Drying Performance
C
Single electric water inlet valve: Voltage
220/ 240 V
Heating element: Power Consumption
1.87/ 2.04 kW
Regeneration valve: Frequency
50/ 60 Hz
Rotations: Spray arm upper
30 RPM - 40 RPM
Flow rates/ Inlet volume: Pump height max.
1.1 m
Flow rates/ Inlet volume: Spray arm lower
~ 33 l/min
Dimensions + Weight: Wooden door for Integrable types (Width)
592 mm - 595 mm
Spray pump motor permant spray system: HI
69 Ω
Dimensions + Weight: Wooden door for Integrable types (Max. stick out over lower edge of appliance door)
92 mm
Water softener: Resin container
700 cm 3
Potentiometer: Points of meassurement: (Position 3)
1.4 k Ω
Heating element: Voltage
220/ 230 V
Flow rates/ Inlet volume: Inlet valve
4 l/min
Accessory:
If you need spare parts apart from the spare part list have a look
in the Service Bulletin 4812 718 40084.
Regeneration: Position 2
after wash cycles 7
Water hardness 11 - 15 °dh 1.9 - 2.7 mmol/l 19 - 27 °Fh
Water softener: Salt container
2 kg
Potentiometer: Points of meassurement: (Position 0)
0.0 k Ω
Options:
Delay function
Electronic boards: Serial boards (CB programmed)
493065
Dimensions + Weight: Wooden door for Integrable types (Height of plinth)
min. 93 mm
Regeneration: Volume
300 cm 3
Drain pump motor: Voltage
220/ 240 V
Regeneration: Position 4
after wash cycles 3
Water hardness 22 - 28 °dh 3.8 - 5.0 mmol/l 38 - 50 °Fh
Detergent capacity: Dosage steps
1 ml - 6 ml
Electrical base data: Total power
2.0 kW - 2.2 kW
Potentiometer: Points of meassurement: (Position 4)
1.8 k Ω
Coil of dispenser: Frequency
50/ 60 Hz
Dimensions + Weight: Product dimensions (Weight)
50 kg
Dimensions + Weight: Wooden door for Integrable types (Height)
515 mm - 600 mm
Flow rates/ Inlet volume: Spray arm upper
~ 27 l/min
Volume: Water Volume Level
Regeneration 0.3 l 15 mm
Back rinse 3x 1.0 l 60 mm
Prewash 4.8 l 120 mm
Main wash 4.2 l 118 mm
Intermediate rinse 1 4.2 l 118 mm
Intermediate rinse 2 4.2 l 118 mm
Clear rinse 4.2 l 118 mm
Safety/ overflow 8.5 l 141 mm
Heating element: Fuse
206 °C
Regeneration valve: Resistance
3.13 k Ω
Electronic boards: Serial boards ()
Programing of version and programmed control board, see "Service" and "Data set" on rating plate of inner door:
Data Energy Label: Energy Performance
A
Flow rates/ Inlet volume: Flow meter
208 lmp/l
Data Energy Label: Reference program
P5e
Размеры + Вес: Размеры продукта (ширина)
59.7 cm
Drain pump motor: Resistance
146 Ω
Succession of programs: Programs ()
see program diagram
Potentiometer: Points of meassurement: (Position 5)
2.3 k Ω
Dimensions + Weight: Wooden door for Integrable types (Thickness)
16 mm - 20 mm
Электрические базовые данные: частота
50 Hz
Coil of dispenser: Voltage
220/ 240 V
NTC
20 °C 58.1 kΩ
25 °C 47.1 kΩ
30 °C 38.2 kΩ
40 °C 25.4 kΩ
50 °C 17.2 kΩ
60 °C 11.8 kΩ
70 °C 8.3 kΩ
80 °C 6 kΩ
85 °C 4 kΩ
Regeneration: Salt consumption for regeneration
77 g
Potentiometer: Points of meassurement: (Position 6)
2.6 k Ω
Электрическая база данных: Предохранитель
10 A
Water pressure: Spray pump pressure
0.3 bar
Размеры + Вес: Размеры продукта (Глубина)
55.5 cm
Regeneration: Position 1
after wash cycles 10
Water hardness 6 - 10 °dh 1 - 1.8 mmol/l 10 - 18 °Fh
Regeneration valve: Voltage
220/ 240 V
Potentiometer: Points of meassurement: (Position 1)
0.5 k Ω
Detergent capacity: Main wash
40 cm 3
Water softener: Regeneration dosage
300 cm 3
Heating element: Resistance
24.5 Ω
Single electric water inlet valve: Frequency
50/ 60 Hz
Spray pump motor permant spray system: HA
48 Ω
Spray pump motor permant spray system: Power Consumption
140 W
Heating element: Heating speed
~ 2.0 °C/min
Rotations: Spray arm lower
30 RPM - 40 RPM
Electronic boards: Serial boards (DUB)
4619 724 82581
Regeneration: Position 6
after wash cycles 1
Water hardness 36 - 60 °dh 6.4 - 10.7 mmol/l 64 - 107 °Fh
Data Energy Label: Cleaning Performance
A
Potentiometer: Points of meassurement: ()
1(black) to 2 (middle)
Spray pump motor permant spray system: Capacitor
4 µ F
Flow rates/ Inlet volume: Drain pump
16 l/min
Regeneration: Position 3
after wash cycles 5
Water hardness 16 - 21 °dh 2.8 - 3.7 mmol/l 28 - 37 °Fh