Схема узла
Запчасти для посудомоечной машины Whirlpool ADG 8347 WH
Характеристики:
Electronic boards: Serial boards CB 730672 (UCB programmed) | 730672 (User/Control board) |
Water pressure: Inlet pressure | 0.3 bar - 10 bar |
Rotations: Drain pump motor | 3000 RPM |
Detergent capacity: Rinse aid dosage | 135 cm 3 |
Dimensions + Weight: Wooden door (Height) | 515 mm - 600 mm |
Flow rates/ Inlet volume: Shower/Spray arm top | ~ 8 l/min |
Spray pump motor permant spray system: Voltage | 220/ 240 V |
Spray pump motor: Voltage | 220/ 240 V |
Heating element: Temperature on surface | ~ 115 °C |
Potentiometer: Points of meassurement: (Position 2) | 1.0 k Ω |
Water softener setting | Härtebereich einstellen (nach folgender Tabelle): Gerät einschalten Programm 2 wählen Start-Taste drücken (mindestens 5 Sekunden) bis Start LED blinkt Start LED blinkt bzw. Digitalanzeige leuchtet entsprechend der eingestellten Härte (siehe Tabelle) Start-Taste kurz drücken ändert die Einstellung um 1 und beginnt nach 7 wieder bei 1 Gerät ausschalten (Einstellung gespeichert) To change the water softener setting:· Push the POWER button on · Change to program 2 · Hold the START button for 5 seconds until the LED is flashing · is shown by flashing LED or digital display · By pushing the START button you can change the setting · Push the POWER button off to save and exit the water softener setting |
Spray pump motor: HA | 48 Ω |
Detergent capacity: Prewash | 10 cm 3 |
Drain pump motor: Power Consumption | 30 W |
Coil of dispenser: Resistance | 1.3 k Ω |
Flow rates/ Inlet volume: Spray pump | 45 l/min - 65 l/min |
Electronic boards: Service boards () | siehe Ersatzteilliste |
Program information: | All programs will be locked after start. Changing the program or ?nishing the program will be possible only after pressing the start button for longer then 1.5 sec. (Break by customer) A switching off the appliance or unplug the appliance for a while, this will frozen the program step and later on, the program continuos on the same position. Exception: Switching off the appliance or unplug the appliance during the drying phase, this will lead directly to the end of the program. |
Электрические базовые данные: напряжение | 220/ 230 V |
Heating element: Safety thermostat self reset (Temperature of water) | ~ 85 °C |
Rotations: Spray pump motor | 2800 RPM |
Heating element: | 1 Element system |
Single electric water inlet valve: Resistance | 3.76 k Ω |
Data Energy Label: Drying Performance | B |
Single electric water inlet valve: Voltage | 220/ 240 V |
Heating element: Power Consumption | 1.87/ 2.04 kW |
Regeneration valve: Frequency | 50/ 60 Hz |
Rotations: Spray arm upper | 30 RPM - 40 RPM |
Flow rates/ Inlet volume: Pump height max. | 1.1 m |
Flow rates/ Inlet volume: Spray arm lower | ~ 33 l/min |
Electronic boards: Serial boards CB 730672 () | Programing of version and programmed control board, see "Service" and "Data set" on rating plate of inner door: |
Spray pump motor permant spray system: HI | 69 Ω |
Water softener: Resin container | 900 cm 3 |
Potentiometer: Points of meassurement: (Position 3) | 1.4 k Ω |
Heating element: Voltage | 220/ 230 V |
Flow rates/ Inlet volume: Inlet valve | 4 l/min |
Accessory: | If you need spare parts apart from the spare part list have a look in the Service Bulletin 4812 718 40084. |
Water softener: Salt container | 2 kg |
Spray pump motor: HI | 69 Ω |
Spray pump motor: Capacitor | 4 µ F |
Potentiometer: Points of meassurement: (Position 0) | 0.0 k Ω |
Dimensions + Weight: Wooden door (Max. stick out over lower edge of appliance door) | 92 mm |
Regeneration: Volume | 300 cm 3 |
Drain pump motor: Voltage | 220/ 240 V |
Detergent capacity: Dosage steps | 1 ml - 6 ml |
Electrical base data: Total power | 2.0 kW - 2.2 kW |
Potentiometer: Points of meassurement: (Position 4) | 1.8 k Ω |
Coil of dispenser: Frequency | 50/ 60 Hz |
Electronic boards: Serial boards CB 730672 (Data set) | 730662 |
Regeneration: after wash cycles | abhängig von der Wasserhärte Depending on the water hardness |
Dimensions + Weight: Product dimensions (Weight) | 55 kg |
Water hardness: Water hardness German degrees °dH French degrees °fH English degrees Clarke °e mmol/l Water softener setting is shown by flashing LED (1x-7x) | 1 soft 0 - 5 0 - 9 0 - 6,3 0 - 0.9 1 x 1 - 2 soft/ medium 6 - 10 10 - 18 7 - 12.6 1 - 1.8 2 x 2 medium 11 - 15 19 - 27 13.3 - 18.9 1.9 - 2.7 3 x 3 medium/ hard 16 - 21 28 - 37 19.6 - 25.9 2.8 - 3.7 4 x (DEFAULT SETTING) 4 hard 22 - 28 38 - 50 26.6 - 35 3.8 - 5.0 5 x 4 very hard 29 - 35 51 - 63 35.7 - 44.1 5.1 - 6.3 6 x 4 extremely hard 36 - 60 (53) 64 - 107 44.8 - 74.9 6.4 - 10.7 7 x 1 weich 0 - 5 0 - 9 0 - 6,3 0 - 0.9 1 x 1 - 2 mittel 6 - 10 10 - 18 7 - 12.6 1 - 1.8 2 x 2 mittel 11 - 15 19 - 27 13.3 - 18.9 1.9 - 2.7 3 x 3 mittelhart 16 - 21 28 - 37 19.6 - 25.9 2.8 - 3.7 4 x (Werkseinstellung) 4 hart 22 - 28 38 - 50 26.6 - 35 3.8 - 5.0 5 x 4 sehr hart 29 - 35 51 - 63 35.7 - 44.1 5.1 - 6.3 6 x 4 äußerst hart 36 - 60 (53) 64 - 107 44.8 - 74.9 6.4 - 10.7 7 x |
Flow rates/ Inlet volume: Spray arm upper | ~ 27 l/min |
Volume: Water Volume Level | Regeneration 0.3 l 15 mm Back rinse 3x 1.0 l 60 mm Prewash 4.8 l 120 mm Main wash 4.2 l 118 mm Intermediate rinse 1 4.2 l 118 mm Intermediate rinse 2 4.2 l 118 mm Clear rinse 4.2 l 118 mm Safety/ overflow 8.5 l 141 mm Regenerieren 0,3 l 15 mm Rückspülen 3x 1,0 l 60 mm Vorspülen 4,8 l 120 mm Hauptspülen 4,2 l 118 mm Zwischenspülen 1 4,2 l 118 mm Zwischenspülen 2 4,2 l 118 mm Klarspülen 4,2 l 118 mm Sicherheitsniveau 8,5 l 141 mm |
Heating element: Fuse | 206 °C |
Regeneration valve: Resistance | 3.13 k Ω |
Data Energy Label: Energy Performance | A |
Flow rates/ Inlet volume: Flow meter | 208 lmp/l |
Data Energy Label: Reference program | P5g |
Размеры + Вес: Размеры продукта (ширина) | 59.7 cm |
Drain pump motor: Resistance | 146 Ω |
Succession of programs: Programs () | see program diagram |
Potentiometer: Points of meassurement: (Position 5) | 2.3 k Ω |
Электрические базовые данные: частота | 50 Hz |
Электрические базовые данные: Потребляемая мощность | 2,0 kW - 2,2 kW |
Coil of dispenser: Voltage | 220/ 240 V |
NTC | 20 °C 58.1 kΩ 25 °C 47.1 kΩ 30 °C 38.2 kΩ 40 °C 25.4 kΩ 50 °C 17.2 kΩ 60 °C 11.8 kΩ 70 °C 8.3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ 20 °C 58,1 kΩ 25 °C 47,1 kΩ 30 °C 38,2 kΩ 40 °C 25,4 kΩ 50 °C 17,2 kΩ 60 °C 11,8 kΩ 70 °C 8,3 kΩ 80 °C 6 kΩ 85 °C 4 kΩ |
Regeneration: Salt consumption for regeneration | ~ 77 g |
Dimensions + Weight: Wooden door (Height of plinth) | min. 93 mm |
Potentiometer: Points of meassurement: (Position 6) | 2.6 k Ω |
Электрическая база данных: Предохранитель | 10 A |
Electronic boards: Serial boards CB 730672 (Basic UCB, not programmed) | 4619 727 27291 see on the board itself |
Water pressure: Spray pump pressure | 0.3 bar |
Размеры + Вес: Размеры продукта (Глубина) | 55.5 cm |
Dimensions + Weight: Wooden door (Width) | 592 mm - 595 mm |
Regeneration valve: Voltage | 220/ 240 V |
Potentiometer: Points of meassurement: (Position 1) | 0.5 k Ω |
Dimensions + Weight: Wooden door (Weight) | max. 5,5 kg |
Detergent capacity: Main wash | 40 cm 3 |
Water softener: Regeneration dosage | 300 cm 3 |
Heating element: Resistance | 24.5 Ω |
Single electric water inlet valve: Frequency | 50/ 60 Hz |
Dimensions + Weight: Wooden door (Thickness) | 16 mm - 20 mm |
Spray pump motor: Power Consumption | 145 W |
Spray pump motor permant spray system: HA | 48 Ω |
Spray pump motor permant spray system: Power Consumption | 145 W |
Heating element: Heating speed | ~ 2.0 °C/min |
Rotations: Spray arm lower | 30 RPM - 40 RPM |
Data Energy Label: Cleaning Performance | A |
Regeneration: Water hardness | 0 - 60 (53) °dh 0 - 10.7 mmol/l 0 - 107 °Fh |
Potentiometer: Points of meassurement: () | 1(black) to 2 (middle) |
Spray pump motor permant spray system: Capacitor | 4 µ F |
Flow rates/ Inlet volume: Drain pump | 16 l/min |
Размеры + Вес: Размеры продукта (Высота) | 82.0 cm - 87.0 cm |
Regeneration: Number of cycles with 2 kg salt | ~ 26 |